Suggestions

Products

DULCOTEST sensors for free chlorine

Graduated measuring ranges 0.01 – 200 mg/l, special measuring range up to 1,000 mg/l

The application-based DULCOTEST sensors for free chlorine deliver precise measured values and a high degree of monitoring and process reliability in any disinfection application.

Send request

Product description

Reliable online measurement of free (effective) chlorine – with DULCOTEST sensors.

Free chlorine is the most important disinfectant in the world. This term is used to refer to the compounds Cl₂ (elementary chlorine), HOCl (hypochlorous acid) and OCl^- (hypochlorite).

Our product line of DULCOTEST sensors for free chlorine provides five product ranges optimised for different applications. Each product range consists of several types with different measuring ranges.

The proven diaphragm-covered standard sensor for free chlorine CLE3 is used to monitor or control all types of clear water, for example in the disinfection of potable water. The variant CLE3.1 is especially suitable for an excess of combined chlorine Mono-, di-, trichloroamine. The measuring result of type CLE (free chlorine) is subtracted from the ... more in the glossary, providing the most accurate results in the calculation of combined chlorine Mono-, di-, trichloroamine. The measuring result of type CLE (free chlorine) is subtracted from the ... more in the glossary from the measurement of total chlorine Total of free and combined chlorine. Recommended sensor: Type CTE, reference method DPD4. more in the glossary and free chlorine.

Sensors CLB2 and CLB3 are easy-to-operate, low-cost chlorine sensors without a diaphragm for clear water without pollution.

Sensor CLO1 is particularly suitable for in-line electrolysis Chlorine and sodium hydroxide are produced in-situ in electrolysis by passing an electric ... more in the glossary processes where unwanted compounds may be formed; sensor CLO2 is also ideal for hot water disinfection.

Sensor CBR1 can be used in contaminated water, even for high pH values of up to 9.5, for example in the disinfection of cooling water.

Sensor CLR1 has been optimised for the disinfection or washing of foodstuffs and tolerates contaminated water and chlorine concentrations of up to 1,000 mg/l.

Your benefits

Five different sensor ranges and numerous different versions deliver the following benefits: use with a wide range of water qualities (pH, salinity, temperature, chemical and contamination load), use in combination with many disinfection processes: chlorine gas, sodium hypochlorite, calcium hypochlorite, electrolysis, use in a wide measuring range of 0.01 to 1,000 mg/l.
Precise, real-time amperometric measurement for efficient process control (short response time)
Amperometric measuring eliminates interference caused by turbidity or colouration
Stable zero point
Integrated temperature compensation eliminates interference caused by influence of temperature
For sensors with diaphragm-covered measuring electrodes: reduced dependence on flow, substances in water and film-forming media. Diaphragm-covered measuring electrodes embedded in an electrolyte ensure long service life. This maintains optimum measuring conditions regardless of process conditions. Low-cost maintenance thanks to easy diaphragm cap changes.

The use of cookies is required to play this video. Here you can adjust your cookie selection to watch this video.
The use of cookies is required to play this video. Here you can adjust your cookie selection to watch this video.

Field of application

The following list of applications are general examples of generally suitable applications for this product. Please contact your local sales representative to talk about the applicable use of this product in your specific case / environment.

Chlorine measurement in potable, swimming pool, cooling, industrial, process, rinsing and wastewater as well as seawater and salt water

Cooling Water Treatment

Efficiency is everything in the cooling water circuit

Everything at ProMinent revolves around the perfect cooling water circuit, which needs to experience few losses over its long life. The precise metering of inhibitors and biocides and suitable filters make this possible.

Utility Water Treatment

It makes economic sense to reuse process water.

Why would you discharge water just because you've used it once? If this water is treated properly, it can be reused with ease, cutting costs in no time.

Waste Water Treatment

Very low-impact treatment for waste water

Our water treatment technology delivers thorough yet environmentally friendly waste water treatment. What's more, with precisely metered additives and optimised processes, you also save money.

Cleaning fruit and vegetables

Simple and reliable cleaning process for agricultural products

Fresh fruit and veg are an essential part of our diet. So it's very important for them to reach the consumer in a safe condition. Precise metering of chlorine dioxide ensures that this is the case.

Technical Details

Free chlorine (hypochlorous acid HOCl)

CLE 3; pH: 5.5 … 8.0; Temp. 5 … 45 °C
CLE3.1; pH: 5.5 … 8.0; Temp. 5 … 45 °C
CLO 3; pH: 5.0 … 9.0; Temp. 5 … 45 °C
CLO 4; pH: 5.0 … 9.0; Temp. 5 … 70 °C
CLB 4; pH: 5.0 … 9.0; Temp. 5 … 45 °C
CLB 5; pH: 5.0 … 9.0; Temp. 5 … 45 °C
CBR 1; pH: 5.0 … 9.5; Temp. 5 … 45 °C
CLR 1; pH: 5.5 … 8.0; Temp. 5 … 45 °C

Sensor for Free Chlorine CLE 3-mA

Standard sensor for measuring free chlorine in clear water. For operation on controllers with 4-20 mA input

Your Benefits

Measured variable: free chlorine, no significant cross-sensitivity to combined chlorine (chloramines)
Diaphragm-covered sensor (encapsulated) minimises faults caused by changing flow or substances in the water

Measured variable	Free chlorine with a pH value < 8
Reference method	DPD1
pH-range	5.5…8.0
Temperature	5…45 °C
Max. pressure	1.0 bar
Flow	DGMa, DLG III: 30...60 l/h BAMa: 5...100 l/h (depending on design)
Supply voltage	16...24 V DC (2-wire)
Output signal	4-20 mA ≈ measuring range, temperature-compensated, uncalibrated, not electrically isolated
Selectivity	Free chlorine as against combined chlorine, even if there is not an excess of it
Disinfection process	Chlorine gas, hypochlorite, electrolysis with diaphragm, disinfectants with organic chlorine, e. g. based on cyanuric acid, are unsuitable
Process integration	Bypass: open sample water outlet
Sensor fitting	BAMa, DGMa, DLG III
Controllers	D1C, DAC, diaLog X, DULCOPOOL Pro
Typical applications	CLE 3-mA-0,5 ppm: potable water; CLE 3-mA-2.0/10 ppm: swimming pools (surfactant-free).
Resistance to	Salts, acids, alkalis. Not surfactants
Measuring principle, technology	Amperometric, 2 electrodes, diaphragm-covered

	Measuring range	Order no.
CLE 3-mA-0.5 ppm	0.01…0.5 mg/l	792927
CLE 3-mA-2 ppm	0.02…2.0 mg/l	792920
CLE 3-mA-5 ppm	0.05…5.0 mg/l	1033392
CLE 3-mA-10 ppm	0.10…10.0 mg/l	792919
CLE 3-mA-20 ppm	0.20…20.0 mg/l	1002964
CLE 3-mA-50 ppm	0.50…50.0 mg/l	1020531
CLE 3-mA-100 ppm	1.00…100.0 mg/l	1022786

Chlorine sensors complete with 100 ml of electrolyte

A mounting kit, order no. 815079, is required for initial fitting of the chlorine sensors in the in-line probe housing DLG III.

Sensor for Free Chlorine CLE 3.1-mA

Sensor for the measurement of free chlorine in clear water with higher selectivity towards combined chlorine. For use on controllers with 4-20 mA input

Your Benefits

Measured variable: free chlorine, no cross-sensitivity to combined chlorine (chloramines), even if there is an excess of it
Diaphragm-covered sensor (encapsulated) minimises faults caused by changing flow or substances in the water

Measured variable	Free chlorine (hypochlorous acid HOCl) with high levels of combined chlorine; for determining the combined chlorine with a DAC controller and sensor for total chlorine type CTE 2-mA or type CTE 3-mA depending on application
Reference method	DPD1
pH-range	5.5…8.0
Temperature	5…45 °C
Max. pressure	1.0 bar
Flow	DGMa, DLG III: 30...60 l/h BAMa: 5...100 l/h (depending on design)
Supply voltage	16...24 V DC (2-wire)
Output signal	4-20 mA ≈ measuring range, temperature-compensated, uncalibrated, not electrically isolated
Selectivity	Free chlorine as against combined chlorine, even if there is an excess of it
Disinfection process	Chlorine gas, hypochlorite, electrolysis with diaphragm, disinfectants with organic chlorine, e. g. based on cyanuric acid, are unsuitable
Process integration	Bypass: open sample water outlet
Sensor fitting	BAMa, DGMa, DLG III
Controllers	D1C, DAC, diaLog X, DULCOPOOL Pro
Typical applications	Potable water with higher volumes of combined chlorine, swimming pools. To determine the combined chlorine from the difference: Total chlorine minus free chlorine in the controller DAC.
Resistance to	Salts, acids, alkalis. Not surfactants
Measuring principle, technology	Amperometric, 2 electrodes, diaphragm-covered

	Measuring range	Order no.
CLE 3.1-mA-0.5 ppm	0.01…0.5 mg/l	1020530
CLE 3.1-mA-2 ppm	0.02…2.0 mg/l	1018369
CLE 3.1-mA-5 ppm	0.05…5.0 mg/l	1019398
CLE 3.1-mA-10 ppm	0.10…10.0 mg/l	1018368

Chlorine sensors complete with 100 ml of electrolyte

A mounting kit, order no. 815079, is required for initial fitting of the chlorine sensors in the in-line probe housing DLG III.

Sensor for Free Chlorine CLE 3-DMT

Standard sensor for measuring free chlorine in clear water. For operation on ProMinent transmitters type DMT

Your Benefits

Measured variable: free chlorine, no significant cross-sensitivity to combined chlorine (chloramines)
Diaphragm-covered sensor (encapsulated) minimises faults caused by changing flow or substances in the water

Measured variable	Free chlorine
Reference method	DPD1
pH-range	5.5…8.0
Temperature	5…45 °C
Max. pressure	1.0 bar
Flow	DGMa, DLG III: 30...60 l/h BAMa: 5...100 l/h (depending on design)
Supply voltage	3.3 V DC (5 P)
Output signal	0…1 V DC, uncalibrated, not temperature-compensated, not electrically isolated
Temperature measurement	About the integrated Pt 1000. The temperature compensation is carried out in DMT.
Selectivity	Free chlorine as against combined chlorine, even if there is not an excess of it
Disinfection process	Chlorine gas, hypochlorite, electrolysis with diaphragm, disinfectants with organic chlorine, e. g. based on cyanuric acid, are unsuitable
Process integration	Bypass: open sample water outlet
Sensor fitting	BAMa, DGMa, DLG III
Controllers	DMT
Typical applications	CLE 3-mA-0,5 ppm: potable water; CLE 3-mA-2.0/10 ppm: swimming pools (surfactant-free).
Resistance to	Salts, acids, alkalis. Not surfactants
Measuring principle, technology	Amperometric, 2 electrodes, diaphragm-covered

	Measuring range	Order no.
CLE 3-DMT-5 ppm	0.01…5.0 mg/l	1005511
CLE 3-DMT-50 ppm	0.10…50.0 mg/l	1005512

Chlorine sensors complete with 100 ml of electrolyte

A mounting kit, order no. 815079, is required for initial fitting of the chlorine sensors in the in-line probe housing DLG III.

Sensor for free chlorine CLE 3-CAN

Standard sensor for measuring free chlorine in clear water. For use on controllers with CAN-bus connection

Your Benefits

Measured variable: free chlorine, no significant cross-sensitivity to combined chlorine (chloramines)
Diaphragm-covered sensor (encapsulated) minimises faults caused by changing flow or substances in the water
Operation on the CAN-bus with all the associated benefits

Measured variable	Free chlorine
Reference method	DPD1
pH-range	5.5…8.0
Temperature	5…45 °C
Max. pressure	1.0 bar
Flow	DGMa, DLG III: 30...60 l/h BAMa: 5...100 l/h (depending on design)
Supply voltage	Via CAN-interface (11 – 30 V)
Output signal	Uncalibrated, temperature compensated, electrically isolated
Selectivity	Free chlorine as against combined chlorine, even if there is not an excess of it
Disinfection process	Chlorine gas, hypochlorite, electrolysis with diaphragm, disinfectants with organic chlorine, e. g. based on cyanuric acid, are unsuitable
Process integration	Bypass: open sample water outlet
Sensor fitting	BAMa, DGMa, DLG III
Controllers	DULCOMARIN
Typical applications	CLE 3-mA-0,5 ppm: potable water; CLE 3-mA-2.0/10 ppm: swimming pools (surfactant-free).
Resistance to	Salts, acids, alkalis. Not surfactants
Measuring principle, technology	Amperometric, 2 electrodes, diaphragm-covered

	Measuring range	Order no.
CLE 3-CAN-10 ppm	0.01…10.0 mg/l	1023425

Chlorine sensors complete with 100 ml of electrolyte

A mounting kit, order no. 815079, is required for initial fitting of the chlorine sensors in the in-line probe housing DLG III.

Sensor for free chlorine CLE 3.1-CAN

Sensor for the measurement of free chlorine in clear water with higher selectivity towards combined chlorine. For use on controllers with CAN-bus connection

Your Benefits

Measured variable: free chlorine, no cross-sensitivity to combined chlorine (chloramines) even if there is an excess of it
Diaphragm-covered sensor (encapsulated) minimises faults caused by changing flow or substances in the water
Operation on the CAN-bus with all the associated benefits

Measured variable	Free chlorine with high levels of combined chlorine; for determining the combined chlorine with a DULCOMARIN and sensor for total chlorine type CTE 2-CAN or type CTE 3-CAN depending on application
Reference method	DPD1
pH-range	5.5…8.0
Temperature	5…45 °C
Max. pressure	1.0 bar
Flow	DGMa, DLG III: 30...60 l/h BAMa: 5...100 l/h (depending on design)
Supply voltage	Via CAN-interface (11 – 30 V)
Output signal	Uncalibrated, temperature compensated, electrically isolated
Selectivity	free chlorine
Disinfection process	Chlorine gas, hypochlorite, electrolysis with diaphragm, disinfectants with organic chlorine, e. g. based on cyanuric acid, are unsuitable
Process integration	Bypass: open sample water outlet
Sensor fitting	BAMa, DGMa, DLG III
Controllers	DULCOMARIN
Typical applications	Drinking water with higher levels of combined chlorine; swimming pool. To determine the combined chlorine from the difference: Total chlorine minus free chlorine in the controller DULCOMARIN.
Resistance to	Salts, acids, alkalis. Not surfactants
Measuring principle, technology	Amperometric, 2 electrodes, diaphragm-covered

	Measuring range	Order no.
CLE 3.1-CAN-10 ppm	0.01…10.0 mg/l	1023426

Chlorine sensors complete with 100 ml of electrolyte

A mounting kit, order no. 815079, is required for initial fitting of the chlorine sensors in the in-line probe housing DLG III.

Sensor for free chlorine CLO 3-mA

Sensor for the measurement of free chlorine in clear water, as well as in seawater, and when using electrolysis processes for disinfection, up to 45 °C (1 bar) or 8 bar (25 °C). For operation with controllers with 4-20 mA input. Also suitable for use in film-forming water with optional "hydrodynamic cleaning".

Your Benefits

Measured variable: free chlorine, no significant cross-sensitivity to combined chlorine (chloramines)
Use when sample water is returned to the process line
Use at higher pressures
Avoidance of problems caused by electrolysis systems in which the electrodes are immersed directly into the sample water
Measurement of free chlorine up to pH 9
Measurement in seawater possible
Also suitable for use in film-forming water with optional "hydrodynamic cleaning".

Measured variable	Free chlorine
Reference method	DPD1
pH-range	5.0…9.0
Temperature	5…45 °C
Max. pressure	8.0 bar (25 °C)
Flow	DGMa, DLG III: 30...60 l/h BAMa: 5...100 l/h (depending on design)
Supply voltage	16...24 V DC (2-wire)
Output signal	4-20 mA ≈ measuring range, temperature-compensated, uncalibrated, not electrically isolated
Selectivity	Free chlorine as against combined chlorine
Disinfection process	Chlorine gas, hypochlorite, electrolysis with diaphragm, electrolysis without diaphragm with electrodes in the process
Process integration	Bypass: open outlet or return of the sample water into the process line, inline: direct installation into the tubes with the INLI fitting
Sensor fitting	BAMa: up to 7 bar/20 °C DGMa up to 6 bar/30 °C DLG III up to 1 bar/55 °C INLI up to 7 bar/40 °C
Controllers	D1C, DAC, AEGIS II, diaLog X, DULCOPOOL Pro
Typical applications	Swimming pools, drinking water, process water and in seawater, and can also be used together with diaphragm-free electrolysis processes. Can also be used in conjunction with hydrodynamic cleaning even in biofilm-forming water, or water containing lime, iron or manganese.
Resistance to	Surfactants, films with using hydrodynamic cleaning
Measuring principle, technology	Amperometric, 3 electrodes, no diaphragm

	Measuring range	Order no.
CLO 3-mA-2 ppm	0.02…2.0 mg/l	1131658
CLO 3-mA-10 ppm	0.10…10.0 mg/l	1131662

Sensor for free chlorine CLO 3-CAN

Sensor for the measurement of free chlorine in clear water even when using electrolysis processes for disinfection, up to 45 °C (1 bar) or 8 bar (25 °C). For use on controllers with CAN-bus connection. Also suitable for use in film-forming water with optional “hydrodynamic cleaning”.

Your Benefits

Measured variable: free chlorine, no significant cross-sensitivity to combined chlorine (chloramines)
Use when sample water is returned to the process line
Use at higher pressures
Avoidance of problems caused by electrolysis systems in which the electrodes are immersed directly into the sample water
Measurement in seawater possible
Also suitable for use in film-forming water with optional "hydrodynamic cleaning".

Measured variable	Free chlorine
Reference method	DPD1
pH-range	5.0…9.0
Temperature	5…45 °C
Max. pressure	8.0 bar (25 °C)
Flow	DGMa, DLG III: 30...60 l/h BAMa: 5...100 l/h (depending on design)
Supply voltage	11…30 V (via CAN interface)
Output signal	Digital (CANopen), uncalibrated, temperature-compensated, electrically isolated
Selectivity	Free chlorine as against combined chlorine
Disinfection process	Chlorine gas, hypochlorite, electrolysis with diaphragm, electrolysis without diaphragm with electrodes in the process
Process integration	Bypass: open outlet or return of the sample water into the process line, inline: direct installation into the tubes with the INLI fitting
Sensor fitting	BAMa: up to 7 bar/20 °C DGMa up to 6 bar/30 °C DLG III up to 1 bar/55 °C INLI up to 7 bar/40 °C
Controllers	DULCOMARIN 3, DULCOMARIN II only with hardware after 06.02.2014 from software version 3035 or later
Typical applications	Swimming pools, drinking water, process water and seawater, and can also be used together with diaphragm-free electrolysis processes. Can also be used in conjunction with hydrodynamic cleaning even in water that forms biofilms, or containing lime, iron or manganese.
Resistance to	Salts, acids, lyes, surfactants, films of dirt, films when using hydrodynamic cleaning
Measuring principle, technology	Amperometric, 3 electrodes, no diaphragm

	Measuring range	Order no.
CLO 3-CAN-10 ppm	0.01…10.0 mg/l	1133203

Sensor for free chlorine CLO 4-mA

Sensor for the measurement of free chlorine in clear water, as well as in seawater, and when using electrolysis processes for disinfection, up to 70 °C or 8 bar (25 °C). For operation with controllers with 4-20 mA input. Also suitable for use in film-forming water with optional "hydrodynamic cleaning".

Your Benefits

Measured variable: free chlorine, no significant cross-sensitivity to combined chlorine (chloramines)
Use when sample water is returned to the process line
Use at higher pressures/temperatures
Avoidance of problems caused by electrolysis systems in which the electrodes are immersed directly into the sample water
Measurement of free chlorine up to pH 9
Measurement in seawater possible
Also suitable for use in film-forming water with optional "hydrodynamic cleaning"

Measured variable	Free chlorine
Reference method	DPD1
pH-range	5.0…9.0
Temperature	5…70 °C
Max. pressure	8.0 bar (25 °C)
Flow	DGMa, DLG III: 30...60 l/h BAMa: 5...100 l/h (depending on design)
Supply voltage	16...24 V DC (2-wire)
Output signal	4-20 mA ≈ measuring range, temperature-compensated, uncalibrated, not electrically isolated
Selectivity	Free chlorine as against combined chlorine
Disinfection process	Chlorine gas, hypochlorite, electrolysis with diaphragm, electrolysis without diaphragm with electrodes in the process
Process integration	Bypass: open outlet or return of the sample water into the process line, inline: direct installation into the tubes with the INLI fitting
Sensor fitting	BAMa: up to 3 bar/70 °C DGMa up to 1 bar/60 °C DLG III up to 1 bar/55 °C INLI up to 2 bar/70 °C
Controllers	D1C, DAC, diaLog X
Typical applications	Hot water up to 70 °C, combating legionella, drinking water, process water and in seawater, can also be used together with diaphragm-free electrolysis processes. Can also be used in conjunction with hydrodynamic cleaning even in biofilm-forming water, or water containing lime, iron or manganese.
Resistance to	Surfactants, films with using hydrodynamic cleaning
Measuring principle, technology	Amperometric, 3 electrodes, no diaphragm

	Measuring range	Order no.
CLO 4-mA-2 ppm	0.02…2.0 mg/l	1131644

Sensor for free chlorine CLB 4-µA

Cost-effective, simple sensor for the measurement of free chlorine in clear water, also in seawater and with a changing media temperature. Can also be used with electrolysis processes for disinfection at up to 45 °C/3 bar. For operation with the Compact controller DCCa

Your Benefits

Measured variable: free chlorine, no significant cross-sensitivity to combined chlorine (chloramines)
Cost-effective due to its simple construction without separate wear parts
Simple, cost-effective maintenance without handling of the diaphragm caps
Avoidance of problems caused by electrolysis systems without a diaphragm in which the electrodes are immersed directly into the sample water
Measurement of free chlorine up to pH 9 and use at high pressure of up to 3 bar thanks to absence of a diaphragm
Measurement in seawater possible

Measured variable	Free chlorine
Measuring range	0.05 – 5.0 mg/l, can be used for short-term shock chlorination up to 10 mg/l
Reference method	DPD1
pH-range	5.0…9.0
Temperature	5…45 °C
Max. pressure	3.0 bar
Flow	DGMa, DLG III: 60...80 l/h BAMa: 5...100 l/h (depending on design)
Supply voltage	Only for compact controllers
Output signal	Unamplified primary flow signal, temperature-compensated, uncalibrated, no electrical isolation.
Selectivity	Free chlorine as against combined chlorine
Disinfection process	Chlorine gas, hypochlorite, electrolysis with diaphragm, electrolysis without diaphragm with electrodes in the process
Process integration	Bypass: open sample water outlet, inline: direct installation into the pipework
Sensor fitting	BAMa, DGMa, DLG III
Controllers	Compact controller
Typical applications	Swimming pools, potable water, seawater, can also be used with diaphragm-free electrolysis processes for chlorine generation, also suitable for use with fluctuating medium temperatures.
Resistance to	surfactants
Measuring principle, technology	Amperometric, 3 electrodes, no diaphragm

	Measuring range	Order no.
CLB 4-µA-5 ppm	0.05…5.0 mg/l	1130517

Sensor for free chlorine CLB 5-µA

Cost-effective, simple sensor for the measurement of free chlorine in clear water, also in seawater and with a constant media temperature. Can also be used with electrolysis processes for disinfection at up to 45 °C/3 bar. For operation with the Compact controller DCCa

Your Benefits

Measured variable: free chlorine, no significant cross-sensitivity to combined chlorine (chloramines)
Cost-effective due to its simple construction without separate wear parts
Simple, cost-effective maintenance without handling of the diaphragm caps
Avoidance of problems caused by electrolysis systems without a diaphragm in which the electrodes are immersed directly into the sample water
Measurement of free chlorine up to pH 9 and use at high pressure of up to 3 bar thanks to absence of a diaphragm
Measurement in seawater possible

Measured variable	Free chlorine
Measuring range	0.05 - 5.0 mg/l: linear, can be used for shock chlorination up to 10.0 mg/l
Reference method	DPD1
pH-range	5.0…9.0
Electrolytic conductivity	0.05...50 mS/cm
Temperature	5…45 °C
Max. pressure	3.0 bar
Flow	DGMa, DLG III: 60...80 l/h BAMa: 5...100 l/h (depending on design)
Supply voltage	Only for compact controllers
Output signal	Non-amplified primary current signal, not temperature-compensated, uncalibrated, not electrically isolated
Temperature measurement	None
Selectivity	Free chlorine as against combined chlorine
Disinfection process	Chlorine gas, hypochlorite, electrolysis with diaphragm, electrolysis without diaphragm with electrodes in the process
Process integration	Bypass: open sample water outlet, inline: direct installation into the pipework; fixed or replaceable (replaceable fitting)
Sensor fitting	BAMa, DGMa, DLG III
Electrical Connection	Fixed cable, 1 m, 4 wires with cable end sleeves
Controllers	Compact controller
Typical applications	Swimming pools, potable water, sea water; also suitable for use with diaphragm-free electrolysis processes for chlorine generation.
Resistance to	surfactants
Measuring principle, technology	Amperometric, 3 electrodes, no diaphragm

	Measuring range	Order no.
CLB 5-µA-5 ppm	0.05…5.0 mg/l	1104626

Sensor for Free Chlorine CBR 1-mA

Sensor for free chlorine and bromine in contaminated water, also suitable for high pH values of up to 9.5. For use with controllers with 4-20 mA input

Your Benefits

Measured variable: free chlorine, as well as free and combined bromine (bromamines)
Diaphragm-covered sensor minimises faults caused by changing flow or ingredients in the water
Resistance to films of dirt and biofilms by electrolyte with antimicrobial effect and large-pore diaphragm
Use at high pH value of up to 9.5 by optimisation of the electrolyte diaphragm system

Measured variable	free chlorine, free bromine, combined bromine, DBDMH (1,3-dibrom-5,5-dimethyl-hydantoin)
Reference method	DPD1
pH-range	5.0…9.5
Temperature	1…40 °C
Max. pressure	1.0 bar
Flow	DGMa: 20...80 l/h DLG III: 40...100 l/h BAMa: 5...100 l/h (depending on design)
Supply voltage	16...24 V DC (2-wire)
Output signal	4-20 mA ≈ measuring range, temperature-compensated, uncalibrated, not electrically isolated
Selectivity	Free chlorine as against combined chlorine
Disinfection process	Chlorine gas, hypochlorite, electrolysis with diaphragm, bromide + hypochlorite
Process integration	Bypass: open sample water outlet
Sensor fitting	BAMa, DGMa, DLG III
Controllers	D1C, DAC, AEGIS II, AEGIS S, diaLog X
Typical applications	Cooling water, process water, waste water, water with higher pH values (stable pH), contaminated swimming pool water. Raw water for drinking water treatment.
Resistance to	Salts, acids, alkalis, surfactants, dirt films
Measuring principle, technology	Amperometric, 2 electrodes, diaphragm-covered

	Measuring range	Order no.
* Measuring range based on chlorine. When measuring bromine, the lower and upper limit of the measuring range are increased by the factor 2.25, therefore for example CBR 1-mA-0.5ppm: 0.02 ...1.1 ppm.
CBR 1-mA-0.5 ppm	0.01…0.5 mg/l *	1038016
CBR 1-mA-2 ppm	0.02…2.0 mg/l *	1038015
CBR 1-mA-5 ppm	0.05…5.0 mg/l *	1052138
CBR 1-mA-10 ppm	0.10…10.0 mg/l *	1038014

Sensor for free chlorine CBR 1-CAN

Sensor for free chlorine and bromine in contaminated water, also suitable for high pH values of up to 9.5. For use on controllers with CAN-bus connection.

Your Benefits

Measured variable: free chlorine as well as free and combined bromine (bromamines)
Diaphragm-covered sensor minimises faults caused by changing flow or ingredients in the water
Resistance to films of dirt and biofilms by electrolyte with antimicrobial effect and large-pore diaphragm
Use at high pH value of up to 9.5 by optimisation of the electrolyte diaphragm system

Measured variable	free chlorine, free bromine, combined bromine, DBDMH (1,3-dibrom-5,5-dimethyl-hydantoin)
Reference method	DPD1
pH-range	5.0…9.5
Temperature	1…40 °C
Max. pressure	1.0 bar
Flow	DGMa: 20...80 l/h DLG III: 40...100 l/h BAMa: 5...100 l/h (depending on design)
Supply voltage	11…30 V DC (via CAN interface)
Output signal	Digital (CANopen), uncalibrated, temperature-compensated, electrically isolated
Selectivity	Free chlorine as against combined chlorine
Disinfection process	Chlorine gas, hypochlorite, electrolysis with diaphragm, bromide + hypochlorite
Process integration	Bypass: open sample water outlet
Sensor fitting	BAMa, DGMa, DLG III
Controllers	DULCOMARIN 3, DULCOMARIN II only with hardware after 06.02.2014 from software version 3035 or later
Typical applications	Cooling water, process water, waste water, water with higher pH values (stable pH), contaminated swimming pool water. Raw water for drinking water treatment.
Resistance to	Dirt films, biofilms, surfactants
Measuring principle, technology	Amperometric, 2 electrodes, diaphragm-covered

	Measuring range	Order no.
CBR 1-CAN-10 ppm	0.01…10.0 mg/l	1122056

Sensor for Free Chlorine CLR 1-mA

Sensor for free chlorine above 10 ppm in contaminated washing water for use with controllers with 4-20 mA input

Your Benefits

Measured variable free chlorine for high concentrations of up to 1,000 ppm
Diaphragm-covered sensor prevents faults caused by changing flow or ingredients in the water
Resistance to films of dirt by pore-free diaphragm

Measured variable	Free chlorine
Reference method	DPD1
pH-range	5.5…8.0
Temperature	5…45 °C
Max. pressure	1.0 bar
Flow	DGMa, DLG III: 40...60 l/h BAMa: 5...100 l/h (depending on design)
Supply voltage	16...24 V DC (2-wire)
Output signal	4-20 mA ≈ measuring range, temperature-compensated, uncalibrated, not electrically isolated
Selectivity	Free chlorine as against combined chlorine
Disinfection process	Chlorine gas, hypochlorite, electrolysis with diaphragm
Process integration	Bypass: open sample water outlet
Sensor fitting	BAMa, DGMa, DLG III
Controllers	D1C, DAC, diaLog X
Typical applications	Salad, vegetable and poultry washing water, contaminated process and wastewater.
Resistance to	Salts, acids, alkalis, surfactants, dirt films
Measuring principle, technology	Amperometric, 2 electrodes, diaphragm-covered

	Measuring range	Order no.
CLR 1-mA-200 ppm	10.0…200 mg/l	1047978

A mounting kit, order no. 815079, is required for initial fitting of the chlorine sensors in the in-line probe housing DLG III.

Downloads for DULCOTEST sensors for free chlorine

Selected filters:

Matching downloads

Sort by Document type

A bis Z

Load more matches ...

No more matches available!

Unfortunately, we did not find an appropriate match.

All words written correctly?
Search again with fewer or different search terms?

Please try again later

Service Unavailable

The server is temporarily unable to service your request due to maintenance downtime or capacity problems. Please try again later.

Overview

Reliable online measurement of free (effective) chlorine – with DULCOTEST sensors.

Free chlorine is the most important disinfectant in the world. This term is used to refer to the compounds Cl₂ (elementary chlorine), HOCl (hypochlorous acid) and OCl^- (hypochlorite).

Sensors CLB2 and CLB3 are easy-to-operate, low-cost chlorine sensors without a diaphragm for clear water without pollution.

Sensor CBR1 can be used in contaminated water, even for high pH values of up to 9.5, for example in the disinfection of cooling water.

Sensor CLR1 has been optimised for the disinfection or washing of foodstuffs and tolerates contaminated water and chlorine concentrations of up to 1,000 mg/l.

Your benefits

Five different sensor ranges and numerous different versions deliver the following benefits: use with a wide range of water qualities (pH, salinity, temperature, chemical and contamination load), use in combination with many disinfection processes: chlorine gas, sodium hypochlorite, calcium hypochlorite, electrolysis, use in a wide measuring range of 0.01 to 1,000 mg/l.
Precise, real-time amperometric measurement for efficient process control (short response time)
Amperometric measuring eliminates interference caused by turbidity or colouration
Stable zero point
Integrated temperature compensation eliminates interference caused by influence of temperature
For sensors with diaphragm-covered measuring electrodes: reduced dependence on flow, substances in water and film-forming media. Diaphragm-covered measuring electrodes embedded in an electrolyte ensure long service life. This maintains optimum measuring conditions regardless of process conditions. Low-cost maintenance thanks to easy diaphragm cap changes.

Video

Application

Technical Data

Technical Details

Free chlorine (hypochlorous acid HOCl)

CLE 3; pH: 5.5 … 8.0; Temp. 5 … 45 °C
CLE3.1; pH: 5.5 … 8.0; Temp. 5 … 45 °C
CLO 3; pH: 5.0 … 9.0; Temp. 5 … 45 °C
CLO 4; pH: 5.0 … 9.0; Temp. 5 … 70 °C
CLB 4; pH: 5.0 … 9.0; Temp. 5 … 45 °C
CLB 5; pH: 5.0 … 9.0; Temp. 5 … 45 °C
CBR 1; pH: 5.0 … 9.5; Temp. 5 … 45 °C
CLR 1; pH: 5.5 … 8.0; Temp. 5 … 45 °C

Sensor for Free Chlorine CLE 3-mA

Standard sensor for measuring free chlorine in clear water. For operation on controllers with 4-20 mA input

Your Benefits

Measured variable: free chlorine, no significant cross-sensitivity to combined chlorine (chloramines)
Diaphragm-covered sensor (encapsulated) minimises faults caused by changing flow or substances in the water

Measured variable	Free chlorine with a pH value < 8
Reference method	DPD1
pH-range	5.5…8.0
Temperature	5…45 °C
Max. pressure	1.0 bar
Flow	DGMa, DLG III: 30...60 l/h BAMa: 5...100 l/h (depending on design)
Supply voltage	16...24 V DC (2-wire)
Output signal	4-20 mA ≈ measuring range, temperature-compensated, uncalibrated, not electrically isolated
Selectivity	Free chlorine as against combined chlorine, even if there is not an excess of it
Disinfection process	Chlorine gas, hypochlorite, electrolysis with diaphragm, disinfectants with organic chlorine, e. g. based on cyanuric acid, are unsuitable
Process integration	Bypass: open sample water outlet
Sensor fitting	BAMa, DGMa, DLG III
Controllers	D1C, DAC, diaLog X, DULCOPOOL Pro
Typical applications	CLE 3-mA-0,5 ppm: potable water; CLE 3-mA-2.0/10 ppm: swimming pools (surfactant-free).
Resistance to	Salts, acids, alkalis. Not surfactants
Measuring principle, technology	Amperometric, 2 electrodes, diaphragm-covered

	Measuring range	Order no.
CLE 3-mA-0.5 ppm	0.01…0.5 mg/l	792927
CLE 3-mA-2 ppm	0.02…2.0 mg/l	792920
CLE 3-mA-5 ppm	0.05…5.0 mg/l	1033392
CLE 3-mA-10 ppm	0.10…10.0 mg/l	792919
CLE 3-mA-20 ppm	0.20…20.0 mg/l	1002964
CLE 3-mA-50 ppm	0.50…50.0 mg/l	1020531
CLE 3-mA-100 ppm	1.00…100.0 mg/l	1022786

Chlorine sensors complete with 100 ml of electrolyte

A mounting kit, order no. 815079, is required for initial fitting of the chlorine sensors in the in-line probe housing DLG III.

Sensor for Free Chlorine CLE 3.1-mA

Sensor for the measurement of free chlorine in clear water with higher selectivity towards combined chlorine. For use on controllers with 4-20 mA input

Your Benefits

Measured variable: free chlorine, no cross-sensitivity to combined chlorine (chloramines), even if there is an excess of it
Diaphragm-covered sensor (encapsulated) minimises faults caused by changing flow or substances in the water

Measured variable	Free chlorine (hypochlorous acid HOCl) with high levels of combined chlorine; for determining the combined chlorine with a DAC controller and sensor for total chlorine type CTE 2-mA or type CTE 3-mA depending on application
Reference method	DPD1
pH-range	5.5…8.0
Temperature	5…45 °C
Max. pressure	1.0 bar
Flow	DGMa, DLG III: 30...60 l/h BAMa: 5...100 l/h (depending on design)
Supply voltage	16...24 V DC (2-wire)
Output signal	4-20 mA ≈ measuring range, temperature-compensated, uncalibrated, not electrically isolated
Selectivity	Free chlorine as against combined chlorine, even if there is an excess of it
Disinfection process	Chlorine gas, hypochlorite, electrolysis with diaphragm, disinfectants with organic chlorine, e. g. based on cyanuric acid, are unsuitable
Process integration	Bypass: open sample water outlet
Sensor fitting	BAMa, DGMa, DLG III
Controllers	D1C, DAC, diaLog X, DULCOPOOL Pro
Typical applications	Potable water with higher volumes of combined chlorine, swimming pools. To determine the combined chlorine from the difference: Total chlorine minus free chlorine in the controller DAC.
Resistance to	Salts, acids, alkalis. Not surfactants
Measuring principle, technology	Amperometric, 2 electrodes, diaphragm-covered

	Measuring range	Order no.
CLE 3.1-mA-0.5 ppm	0.01…0.5 mg/l	1020530
CLE 3.1-mA-2 ppm	0.02…2.0 mg/l	1018369
CLE 3.1-mA-5 ppm	0.05…5.0 mg/l	1019398
CLE 3.1-mA-10 ppm	0.10…10.0 mg/l	1018368

Chlorine sensors complete with 100 ml of electrolyte

A mounting kit, order no. 815079, is required for initial fitting of the chlorine sensors in the in-line probe housing DLG III.

Sensor for Free Chlorine CLE 3-DMT

Standard sensor for measuring free chlorine in clear water. For operation on ProMinent transmitters type DMT

Your Benefits

Measured variable: free chlorine, no significant cross-sensitivity to combined chlorine (chloramines)
Diaphragm-covered sensor (encapsulated) minimises faults caused by changing flow or substances in the water

Measured variable	Free chlorine
Reference method	DPD1
pH-range	5.5…8.0
Temperature	5…45 °C
Max. pressure	1.0 bar
Flow	DGMa, DLG III: 30...60 l/h BAMa: 5...100 l/h (depending on design)
Supply voltage	3.3 V DC (5 P)
Output signal	0…1 V DC, uncalibrated, not temperature-compensated, not electrically isolated
Temperature measurement	About the integrated Pt 1000. The temperature compensation is carried out in DMT.
Selectivity	Free chlorine as against combined chlorine, even if there is not an excess of it
Disinfection process	Chlorine gas, hypochlorite, electrolysis with diaphragm, disinfectants with organic chlorine, e. g. based on cyanuric acid, are unsuitable
Process integration	Bypass: open sample water outlet
Sensor fitting	BAMa, DGMa, DLG III
Controllers	DMT
Typical applications	CLE 3-mA-0,5 ppm: potable water; CLE 3-mA-2.0/10 ppm: swimming pools (surfactant-free).
Resistance to	Salts, acids, alkalis. Not surfactants
Measuring principle, technology	Amperometric, 2 electrodes, diaphragm-covered

	Measuring range	Order no.
CLE 3-DMT-5 ppm	0.01…5.0 mg/l	1005511
CLE 3-DMT-50 ppm	0.10…50.0 mg/l	1005512

Chlorine sensors complete with 100 ml of electrolyte

A mounting kit, order no. 815079, is required for initial fitting of the chlorine sensors in the in-line probe housing DLG III.

Sensor for free chlorine CLE 3-CAN

Standard sensor for measuring free chlorine in clear water. For use on controllers with CAN-bus connection

Your Benefits

Measured variable: free chlorine, no significant cross-sensitivity to combined chlorine (chloramines)
Diaphragm-covered sensor (encapsulated) minimises faults caused by changing flow or substances in the water
Operation on the CAN-bus with all the associated benefits

Measured variable	Free chlorine
Reference method	DPD1
pH-range	5.5…8.0
Temperature	5…45 °C
Max. pressure	1.0 bar
Flow	DGMa, DLG III: 30...60 l/h BAMa: 5...100 l/h (depending on design)
Supply voltage	Via CAN-interface (11 – 30 V)
Output signal	Uncalibrated, temperature compensated, electrically isolated
Selectivity	Free chlorine as against combined chlorine, even if there is not an excess of it
Disinfection process	Chlorine gas, hypochlorite, electrolysis with diaphragm, disinfectants with organic chlorine, e. g. based on cyanuric acid, are unsuitable
Process integration	Bypass: open sample water outlet
Sensor fitting	BAMa, DGMa, DLG III
Controllers	DULCOMARIN
Typical applications	CLE 3-mA-0,5 ppm: potable water; CLE 3-mA-2.0/10 ppm: swimming pools (surfactant-free).
Resistance to	Salts, acids, alkalis. Not surfactants
Measuring principle, technology	Amperometric, 2 electrodes, diaphragm-covered

	Measuring range	Order no.
CLE 3-CAN-10 ppm	0.01…10.0 mg/l	1023425

Chlorine sensors complete with 100 ml of electrolyte

A mounting kit, order no. 815079, is required for initial fitting of the chlorine sensors in the in-line probe housing DLG III.

Sensor for free chlorine CLE 3.1-CAN

Sensor for the measurement of free chlorine in clear water with higher selectivity towards combined chlorine. For use on controllers with CAN-bus connection

Your Benefits

Measured variable: free chlorine, no cross-sensitivity to combined chlorine (chloramines) even if there is an excess of it
Diaphragm-covered sensor (encapsulated) minimises faults caused by changing flow or substances in the water
Operation on the CAN-bus with all the associated benefits

Measured variable	Free chlorine with high levels of combined chlorine; for determining the combined chlorine with a DULCOMARIN and sensor for total chlorine type CTE 2-CAN or type CTE 3-CAN depending on application
Reference method	DPD1
pH-range	5.5…8.0
Temperature	5…45 °C
Max. pressure	1.0 bar
Flow	DGMa, DLG III: 30...60 l/h BAMa: 5...100 l/h (depending on design)
Supply voltage	Via CAN-interface (11 – 30 V)
Output signal	Uncalibrated, temperature compensated, electrically isolated
Selectivity	free chlorine
Disinfection process	Chlorine gas, hypochlorite, electrolysis with diaphragm, disinfectants with organic chlorine, e. g. based on cyanuric acid, are unsuitable
Process integration	Bypass: open sample water outlet
Sensor fitting	BAMa, DGMa, DLG III
Controllers	DULCOMARIN
Typical applications	Drinking water with higher levels of combined chlorine; swimming pool. To determine the combined chlorine from the difference: Total chlorine minus free chlorine in the controller DULCOMARIN.
Resistance to	Salts, acids, alkalis. Not surfactants
Measuring principle, technology	Amperometric, 2 electrodes, diaphragm-covered

	Measuring range	Order no.
CLE 3.1-CAN-10 ppm	0.01…10.0 mg/l	1023426

Chlorine sensors complete with 100 ml of electrolyte

A mounting kit, order no. 815079, is required for initial fitting of the chlorine sensors in the in-line probe housing DLG III.

Sensor for free chlorine CLO 3-mA

Your Benefits

Measured variable: free chlorine, no significant cross-sensitivity to combined chlorine (chloramines)
Use when sample water is returned to the process line
Use at higher pressures
Avoidance of problems caused by electrolysis systems in which the electrodes are immersed directly into the sample water
Measurement of free chlorine up to pH 9
Measurement in seawater possible
Also suitable for use in film-forming water with optional "hydrodynamic cleaning".

Measured variable	Free chlorine
Reference method	DPD1
pH-range	5.0…9.0
Temperature	5…45 °C
Max. pressure	8.0 bar (25 °C)
Flow	DGMa, DLG III: 30...60 l/h BAMa: 5...100 l/h (depending on design)
Supply voltage	16...24 V DC (2-wire)
Output signal	4-20 mA ≈ measuring range, temperature-compensated, uncalibrated, not electrically isolated
Selectivity	Free chlorine as against combined chlorine
Disinfection process	Chlorine gas, hypochlorite, electrolysis with diaphragm, electrolysis without diaphragm with electrodes in the process
Process integration	Bypass: open outlet or return of the sample water into the process line, inline: direct installation into the tubes with the INLI fitting
Sensor fitting	BAMa: up to 7 bar/20 °C DGMa up to 6 bar/30 °C DLG III up to 1 bar/55 °C INLI up to 7 bar/40 °C
Controllers	D1C, DAC, AEGIS II, diaLog X, DULCOPOOL Pro
Typical applications	Swimming pools, drinking water, process water and in seawater, and can also be used together with diaphragm-free electrolysis processes. Can also be used in conjunction with hydrodynamic cleaning even in biofilm-forming water, or water containing lime, iron or manganese.
Resistance to	Surfactants, films with using hydrodynamic cleaning
Measuring principle, technology	Amperometric, 3 electrodes, no diaphragm

	Measuring range	Order no.
CLO 3-mA-2 ppm	0.02…2.0 mg/l	1131658
CLO 3-mA-10 ppm	0.10…10.0 mg/l	1131662

Sensor for free chlorine CLO 3-CAN

Your Benefits

Measured variable: free chlorine, no significant cross-sensitivity to combined chlorine (chloramines)
Use when sample water is returned to the process line
Use at higher pressures
Avoidance of problems caused by electrolysis systems in which the electrodes are immersed directly into the sample water
Measurement in seawater possible
Also suitable for use in film-forming water with optional "hydrodynamic cleaning".

Measured variable	Free chlorine
Reference method	DPD1
pH-range	5.0…9.0
Temperature	5…45 °C
Max. pressure	8.0 bar (25 °C)
Flow	DGMa, DLG III: 30...60 l/h BAMa: 5...100 l/h (depending on design)
Supply voltage	11…30 V (via CAN interface)
Output signal	Digital (CANopen), uncalibrated, temperature-compensated, electrically isolated
Selectivity	Free chlorine as against combined chlorine
Disinfection process	Chlorine gas, hypochlorite, electrolysis with diaphragm, electrolysis without diaphragm with electrodes in the process
Process integration	Bypass: open outlet or return of the sample water into the process line, inline: direct installation into the tubes with the INLI fitting
Sensor fitting	BAMa: up to 7 bar/20 °C DGMa up to 6 bar/30 °C DLG III up to 1 bar/55 °C INLI up to 7 bar/40 °C
Controllers	DULCOMARIN 3, DULCOMARIN II only with hardware after 06.02.2014 from software version 3035 or later
Typical applications	Swimming pools, drinking water, process water and seawater, and can also be used together with diaphragm-free electrolysis processes. Can also be used in conjunction with hydrodynamic cleaning even in water that forms biofilms, or containing lime, iron or manganese.
Resistance to	Salts, acids, lyes, surfactants, films of dirt, films when using hydrodynamic cleaning
Measuring principle, technology	Amperometric, 3 electrodes, no diaphragm

	Measuring range	Order no.
CLO 3-CAN-10 ppm	0.01…10.0 mg/l	1133203

Sensor for free chlorine CLO 4-mA

Your Benefits

Measured variable: free chlorine, no significant cross-sensitivity to combined chlorine (chloramines)
Use when sample water is returned to the process line
Use at higher pressures/temperatures
Avoidance of problems caused by electrolysis systems in which the electrodes are immersed directly into the sample water
Measurement of free chlorine up to pH 9
Measurement in seawater possible
Also suitable for use in film-forming water with optional "hydrodynamic cleaning"

Measured variable	Free chlorine
Reference method	DPD1
pH-range	5.0…9.0
Temperature	5…70 °C
Max. pressure	8.0 bar (25 °C)
Flow	DGMa, DLG III: 30...60 l/h BAMa: 5...100 l/h (depending on design)
Supply voltage	16...24 V DC (2-wire)
Output signal	4-20 mA ≈ measuring range, temperature-compensated, uncalibrated, not electrically isolated
Selectivity	Free chlorine as against combined chlorine
Disinfection process	Chlorine gas, hypochlorite, electrolysis with diaphragm, electrolysis without diaphragm with electrodes in the process
Process integration	Bypass: open outlet or return of the sample water into the process line, inline: direct installation into the tubes with the INLI fitting
Sensor fitting	BAMa: up to 3 bar/70 °C DGMa up to 1 bar/60 °C DLG III up to 1 bar/55 °C INLI up to 2 bar/70 °C
Controllers	D1C, DAC, diaLog X
Typical applications	Hot water up to 70 °C, combating legionella, drinking water, process water and in seawater, can also be used together with diaphragm-free electrolysis processes. Can also be used in conjunction with hydrodynamic cleaning even in biofilm-forming water, or water containing lime, iron or manganese.
Resistance to	Surfactants, films with using hydrodynamic cleaning
Measuring principle, technology	Amperometric, 3 electrodes, no diaphragm

	Measuring range	Order no.
CLO 4-mA-2 ppm	0.02…2.0 mg/l	1131644

Sensor for free chlorine CLB 4-µA

Your Benefits

Measured variable: free chlorine, no significant cross-sensitivity to combined chlorine (chloramines)
Cost-effective due to its simple construction without separate wear parts
Simple, cost-effective maintenance without handling of the diaphragm caps
Avoidance of problems caused by electrolysis systems without a diaphragm in which the electrodes are immersed directly into the sample water
Measurement of free chlorine up to pH 9 and use at high pressure of up to 3 bar thanks to absence of a diaphragm
Measurement in seawater possible

Measured variable	Free chlorine
Measuring range	0.05 – 5.0 mg/l, can be used for short-term shock chlorination up to 10 mg/l
Reference method	DPD1
pH-range	5.0…9.0
Temperature	5…45 °C
Max. pressure	3.0 bar
Flow	DGMa, DLG III: 60...80 l/h BAMa: 5...100 l/h (depending on design)
Supply voltage	Only for compact controllers
Output signal	Unamplified primary flow signal, temperature-compensated, uncalibrated, no electrical isolation.
Selectivity	Free chlorine as against combined chlorine
Disinfection process	Chlorine gas, hypochlorite, electrolysis with diaphragm, electrolysis without diaphragm with electrodes in the process
Process integration	Bypass: open sample water outlet, inline: direct installation into the pipework
Sensor fitting	BAMa, DGMa, DLG III
Controllers	Compact controller
Typical applications	Swimming pools, potable water, seawater, can also be used with diaphragm-free electrolysis processes for chlorine generation, also suitable for use with fluctuating medium temperatures.
Resistance to	surfactants
Measuring principle, technology	Amperometric, 3 electrodes, no diaphragm

	Measuring range	Order no.
CLB 4-µA-5 ppm	0.05…5.0 mg/l	1130517

Sensor for free chlorine CLB 5-µA

Your Benefits

Measured variable: free chlorine, no significant cross-sensitivity to combined chlorine (chloramines)
Cost-effective due to its simple construction without separate wear parts
Simple, cost-effective maintenance without handling of the diaphragm caps
Avoidance of problems caused by electrolysis systems without a diaphragm in which the electrodes are immersed directly into the sample water
Measurement of free chlorine up to pH 9 and use at high pressure of up to 3 bar thanks to absence of a diaphragm
Measurement in seawater possible

Measured variable	Free chlorine
Measuring range	0.05 - 5.0 mg/l: linear, can be used for shock chlorination up to 10.0 mg/l
Reference method	DPD1
pH-range	5.0…9.0
Electrolytic conductivity	0.05...50 mS/cm
Temperature	5…45 °C
Max. pressure	3.0 bar
Flow	DGMa, DLG III: 60...80 l/h BAMa: 5...100 l/h (depending on design)
Supply voltage	Only for compact controllers
Output signal	Non-amplified primary current signal, not temperature-compensated, uncalibrated, not electrically isolated
Temperature measurement	None
Selectivity	Free chlorine as against combined chlorine
Disinfection process	Chlorine gas, hypochlorite, electrolysis with diaphragm, electrolysis without diaphragm with electrodes in the process
Process integration	Bypass: open sample water outlet, inline: direct installation into the pipework; fixed or replaceable (replaceable fitting)
Sensor fitting	BAMa, DGMa, DLG III
Electrical Connection	Fixed cable, 1 m, 4 wires with cable end sleeves
Controllers	Compact controller
Typical applications	Swimming pools, potable water, sea water; also suitable for use with diaphragm-free electrolysis processes for chlorine generation.
Resistance to	surfactants
Measuring principle, technology	Amperometric, 3 electrodes, no diaphragm

	Measuring range	Order no.
CLB 5-µA-5 ppm	0.05…5.0 mg/l	1104626

Sensor for Free Chlorine CBR 1-mA

Sensor for free chlorine and bromine in contaminated water, also suitable for high pH values of up to 9.5. For use with controllers with 4-20 mA input

Your Benefits

Measured variable: free chlorine, as well as free and combined bromine (bromamines)
Diaphragm-covered sensor minimises faults caused by changing flow or ingredients in the water
Resistance to films of dirt and biofilms by electrolyte with antimicrobial effect and large-pore diaphragm
Use at high pH value of up to 9.5 by optimisation of the electrolyte diaphragm system

Measured variable	free chlorine, free bromine, combined bromine, DBDMH (1,3-dibrom-5,5-dimethyl-hydantoin)
Reference method	DPD1
pH-range	5.0…9.5
Temperature	1…40 °C
Max. pressure	1.0 bar
Flow	DGMa: 20...80 l/h DLG III: 40...100 l/h BAMa: 5...100 l/h (depending on design)
Supply voltage	16...24 V DC (2-wire)
Output signal	4-20 mA ≈ measuring range, temperature-compensated, uncalibrated, not electrically isolated
Selectivity	Free chlorine as against combined chlorine
Disinfection process	Chlorine gas, hypochlorite, electrolysis with diaphragm, bromide + hypochlorite
Process integration	Bypass: open sample water outlet
Sensor fitting	BAMa, DGMa, DLG III
Controllers	D1C, DAC, AEGIS II, AEGIS S, diaLog X
Typical applications	Cooling water, process water, waste water, water with higher pH values (stable pH), contaminated swimming pool water. Raw water for drinking water treatment.
Resistance to	Salts, acids, alkalis, surfactants, dirt films
Measuring principle, technology	Amperometric, 2 electrodes, diaphragm-covered

	Measuring range	Order no.
* Measuring range based on chlorine. When measuring bromine, the lower and upper limit of the measuring range are increased by the factor 2.25, therefore for example CBR 1-mA-0.5ppm: 0.02 ...1.1 ppm.
CBR 1-mA-0.5 ppm	0.01…0.5 mg/l *	1038016
CBR 1-mA-2 ppm	0.02…2.0 mg/l *	1038015
CBR 1-mA-5 ppm	0.05…5.0 mg/l *	1052138
CBR 1-mA-10 ppm	0.10…10.0 mg/l *	1038014

Sensor for free chlorine CBR 1-CAN

Sensor for free chlorine and bromine in contaminated water, also suitable for high pH values of up to 9.5. For use on controllers with CAN-bus connection.

Your Benefits

Measured variable: free chlorine as well as free and combined bromine (bromamines)
Diaphragm-covered sensor minimises faults caused by changing flow or ingredients in the water
Resistance to films of dirt and biofilms by electrolyte with antimicrobial effect and large-pore diaphragm
Use at high pH value of up to 9.5 by optimisation of the electrolyte diaphragm system

Measured variable	free chlorine, free bromine, combined bromine, DBDMH (1,3-dibrom-5,5-dimethyl-hydantoin)
Reference method	DPD1
pH-range	5.0…9.5
Temperature	1…40 °C
Max. pressure	1.0 bar
Flow	DGMa: 20...80 l/h DLG III: 40...100 l/h BAMa: 5...100 l/h (depending on design)
Supply voltage	11…30 V DC (via CAN interface)
Output signal	Digital (CANopen), uncalibrated, temperature-compensated, electrically isolated
Selectivity	Free chlorine as against combined chlorine
Disinfection process	Chlorine gas, hypochlorite, electrolysis with diaphragm, bromide + hypochlorite
Process integration	Bypass: open sample water outlet
Sensor fitting	BAMa, DGMa, DLG III
Controllers	DULCOMARIN 3, DULCOMARIN II only with hardware after 06.02.2014 from software version 3035 or later
Typical applications	Cooling water, process water, waste water, water with higher pH values (stable pH), contaminated swimming pool water. Raw water for drinking water treatment.
Resistance to	Dirt films, biofilms, surfactants
Measuring principle, technology	Amperometric, 2 electrodes, diaphragm-covered

	Measuring range	Order no.
CBR 1-CAN-10 ppm	0.01…10.0 mg/l	1122056

Sensor for Free Chlorine CLR 1-mA

Sensor for free chlorine above 10 ppm in contaminated washing water for use with controllers with 4-20 mA input

Your Benefits

Measured variable free chlorine for high concentrations of up to 1,000 ppm
Diaphragm-covered sensor prevents faults caused by changing flow or ingredients in the water
Resistance to films of dirt by pore-free diaphragm

Measured variable	Free chlorine
Reference method	DPD1
pH-range	5.5…8.0
Temperature	5…45 °C
Max. pressure	1.0 bar
Flow	DGMa, DLG III: 40...60 l/h BAMa: 5...100 l/h (depending on design)
Supply voltage	16...24 V DC (2-wire)
Output signal	4-20 mA ≈ measuring range, temperature-compensated, uncalibrated, not electrically isolated
Selectivity	Free chlorine as against combined chlorine
Disinfection process	Chlorine gas, hypochlorite, electrolysis with diaphragm
Process integration	Bypass: open sample water outlet
Sensor fitting	BAMa, DGMa, DLG III
Controllers	D1C, DAC, diaLog X
Typical applications	Salad, vegetable and poultry washing water, contaminated process and wastewater.
Resistance to	Salts, acids, alkalis, surfactants, dirt films
Measuring principle, technology	Amperometric, 2 electrodes, diaphragm-covered

	Measuring range	Order no.
CLR 1-mA-200 ppm	10.0…200 mg/l	1047978

A mounting kit, order no. 815079, is required for initial fitting of the chlorine sensors in the in-line probe housing DLG III.

Downloads

Contact us

Wesley Sutton

Managing Director, ProMinent Fluid Controls UK Ltd.

+44 1530 560 555
Send request

»We are always available to help. Don't hesitate to contact us.«

+44 1530 560 555 Send request

Spare Parts and Accessories

Matching Products

DULCOTEST ORP sensors

Typical measuring range -1,500...+1,500 mV; wider ranges are possible depending on the measuring device.

ORP measurements with DULCOTEST sensors: Precise, reliable and application-adapted measured values in real-time. Can be used in water treatment or industrial process waters with strict requirements.

DULCOTEST pH sensors

Graduated pH measuring ranges 0 – 14

pH measurements with DULCOTEST sensors: Precise, reliable and application-adapted measured values in real-time. Control, regulate and monitor chemical processes with the aid of precise measured values.

Controller DULCOMETER diaLog DACb

Do you wish for a simple controller for water analysis? One that is easy to operate and with which you can freely select between all common measured variables per channel? There is one: our all-rounder DULCOMETER diaLog DACb! What is more, it is Ethernet-/LAN-capable and can be ideally integrated into existing networks.

Controller DULCOMETER D1Cb/D1Cc

The controller DULCOMETER D1Cb/D1Cc can be used for control tasks in potable water treatment, wastewater treatment and many other areas. Safe, convenient and clear, thanks to the large illuminated graphic display, plain text operating menu and pH sensor monitoring.

Measuring and control system DULCOMARIN 3

The measuring and control system DULCOMARIN 3 is your digital link to the technology of the future. It controls the entire range of swimming pools – from adventure pools to private pools – and is used as a multi-pool system for up to 16 filter circuits.